Umut

Toyota / Subaru SRS H8SX Boot Mode Diagrams

43 posts in this topic

hello 

Toyota Subaru H8SX Boot Mode. how to connect resistor and where to connect

it is different SRS block by block. all not same

if some one have problem how to connect boot mode please upload clear pictures and ask . i will help you how to do that 

TSRS1.PNG

tsrs2.PNG

TSRS3.PNG

TSRS4.PNG

TSRS5.PNG

TSRS6.PNG

TSRS7.PNG

Share this post


Link to post
Share on other sites

Do you have problem how to connect Boot mode resistor please send us clear pictures. We will help you 

 

Share this post


Link to post
Share on other sites
17 minutes ago, Carnostics said:

I have the same module. anyone know how to connect for boot mode ? 89170-0E120 AS 89170-06720

 

 

MCU number ??

Share this post


Link to post
Share on other sites
1 minute ago, Carnostics said:

does anybody have boot mode connection for 2015 corolla

this is different board layout. it has 1725 mcu

IMG_7328.JPG

IMG_7329.JPG

find mcu pin 66 and remove 0 ohm resistor then connect 10kohm - 47kohm resistor to 5v and pin 66 

Share this post


Link to post
Share on other sites

which 0 ohm resistor. I cant see any ohm resistor near renesas mcu or reset or 5v connection. I can read flash erase but cant erase eeprom or write flash back. 

anyone have boot mode connection for this. I just received another one 89170-0k600 2015 hilux. same board. only picture I have for help is from cpt.

Toyota-R5F6172X-CPT_V7.jpg

Share this post


Link to post
Share on other sites

Здравствуйте. Подскажите пожалуйста как перевести в бут режим SRS DENSO 89170-47680, mcu: R5F61797

20171127_185921[1].jpg

20171127_185857[1].jpg

Edited by funki

Share this post


Link to post
Share on other sites

reset подтянуть через резистор 10Kom к +5v,посмотри чтоб эта ножка не на чём больше не сидела. 

Share this post


Link to post
Share on other sites
В 28.11.2017 в 10:22, kilya31 сказал:

reset подтянуть через резистор 10Kom к +5v,посмотри чтоб эта ножка не на чём больше не сидела. 

А так разве не в бут переводится

Share this post


Link to post
Share on other sites
On 11/28/2017 at 3:07 AM, funki said:

Здравствуйтею Подскажите пожалуйста как перевести в бут режим SRS DENSO 89170-47680, mcu: R5F61797

20171127_185921[1].jpg

20171127_185857[1].jpg

 

Share this post


Link to post
Share on other sites
В 14.04.2018 в 00:24, ayadwireman сказал:

 

не получается забутить этот блок.ньюансов  нет никаких?

припаял 10к непосредственно на ноги проца,с другой стороны резистор убрал

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.