GROM

Nissan SRS infineon

13 posts in this topic

Одним из первых сделан модуль для блоков SRS NISSAN на процессорах Infineon
 
Модуль читает - записывает eeprom процессора, читает - стирает ошибки, удаляет данные об аварии из дампа.

2020-07-24_19-22-42.jpg

2020-07-24_19-23-01.jpg

 

Видео по работе.

 

Обсуждение работы модуля в этой теме.

Share this post


Link to post
Share on other sites

Nissan give code DTC B1421 Uncnow CODE Or Code not active.. Code is really B1421 Frontal Collision

These are the description for nissan codes.

DTC   B1431 RH Seat Belt Circuit is Open.
DTC   B1430 LH Seat Belt Circuit is Open. 
DTC   B1433 RH Seat Belt Pre-Tensioner Circuit is open.
DTC   B1432 LH Seat Belt Pre-Tensioner Circuit is open.

Share this post


Link to post
Share on other sites
9 hours ago, cjohny said:

Здравствуйте! Вот дополненный файл с ошибками .Просто замените в программе.

obdcodes_Nissan.txt

I have that but those codes I listed need to be added to the scanner. all those codes I added are unknown.

Share this post


Link to post
Share on other sites

Замените файл в программе и все будет отображаться при диагностике.

2017-05-18_19-02-29.png.8da10baec85897140d57b0d8f7be9f7e.png

Share this post


Link to post
Share on other sites

Nice...that is not in my obdcodes_Nissan.txt file...

I had given him some codes before maybe he added it?

Share this post


Link to post
Share on other sites

Вы можете сами добавлять коды которые не найдете в программе в текстовый файл открыв блокнотом Windows.

SRS NISSAN FAULT.pdf

Share this post


Link to post
Share on other sites
1 minute ago, cjohny said:

Вы можете сами добавлять коды которые не найдете в программе в текстовый файл открыв блокнотом Windows.

SRS NISSAN FAULT.pdf

Thank you but I know what the codes are...I would just like for him to add it to scanner.

Share this post


Link to post
Share on other sites

Lately tool have issue writing...read flash from infineon ok then load good clear file and sometimes I have to write it 2-4 times to module before it actually go through. anyone else having this issue?

Share this post


Link to post
Share on other sites

В обновлении, будет функция изменения скорости CAN BUS (Скорость обработки пакетов), она была увеличена, но проблем не было, если это повторится, можно попробовать будет понизить скорость обмена.

Вскоре будет добавлена поддержка J2534 устройств, там скорость обмена будет высокой.

Share this post


Link to post
Share on other sites

Да и читает инфинеон долговато, и запись не с первого  раза проходит,я думаю поддержка j2534 спасёт :))

Share this post


Link to post
Share on other sites

Yes I notice read can be a bit long but read always ok...writing is fast but not always ok..good idea to be able to set speed. 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.