Sign in to follow this  
Followers 0
kamilek1307

Problem with GprogPro programmer after last update

8 posts in this topic

Hello,

I am using GPROG programmer mainly for SUBARU RH850 srs. It worked fine till last update.
Now I see information: programmer disconnect and I am not able to do anything. 

24.05.2024, 13.18.46]      Check key...
[24.05.2024, 13.18.46]      
[24.05.2024, 13.18.47]      Key ID: 431Cxxxx
[24.05.2024, 13.18.47]      
[24.05.2024, 13.18.47]      Key OK!
[24.05.2024, 13.18.47]      DONGLE [ USER ID: 431Cxxxx ]    
[24.05.2024, 13.18.47]      Programm version: 1.0.0.172
[24.05.2024, 13.18.47]      VCC value: 3.3 V
[24.05.2024, 13.18.47]      Connect programmer: GPROG S/N:   4F4A393150162xxxxxx    F/W:   0024   COM4
[24.05.2024, 13.18.48]      

Key ID: 431Cxxxx

Syncronization...

The download from the database has been completed!
The key is validated. Launch counter updated!
There is no full license!
There is no Probyte full license!


The check in the database is finished!
Syncronization OK!

[24.05.2024, 13.18.55]      Selected device:   CHIP   Subaru_SRS_Lock_MCU_R7F701686
[24.05.2024, 13.19.02]      Check key...
[24.05.2024, 13.19.02]      
[24.05.2024, 13.19.02]      Key ID: 431Cxxxx
[24.05.2024, 13.19.03]      
[24.05.2024, 13.19.03]      Key OK!
[24.05.2024, 13.19.03]      DONGLE [ USER ID: 431Cxxxx ]    
[24.05.2024, 13.19.03]      Programm version: 1.0.0.172
[24.05.2024, 13.19.03]      VCC value: 3.3 V
[24.05.2024, 13.19.03]      Programmer disconnect
[24.05.2024, 13.19.03]      Programmer disconnect
[24.05.2024, 13.19.03]      Programmer Error! SEC BOOT Function canceled!

Share this post


Link to post
Share on other sites

Передернуть провод юсб пробовали? Программу перезапустить, а так же компьютер

Share this post


Link to post
Share on other sites

I have this issue on 3 PCs, i checked 3 cables. same issue. 

I restarted computers, disconnected device, and program. 

Issue appeard after last update 1.0.0.172. Before update it worked ok. 
I updated one PC 2 days ago and issue occurs. But programmer worked on another computer where I had older version, but today i updated it by mistake. And same issue on each of them. 

Share this post


Link to post
Share on other sites

Wenesday I done one without any issue with update version 

In my side no issue come. 

Even my side updated. 

Share this post


Link to post
Share on other sites

Programmer is detected correctly when I start the GprogPro aplication. And started to be "disconnected" even I go to "system>Gprog information"
I bought this programmer from official reseler IOBD.

Share this post


Link to post
Share on other sites

Check another module for test not subaru lock mcu

ANY other eeprom or any other module 

 

Share this post


Link to post
Share on other sites

Error is visible when I haven't got connected any module too. there is no connection to srs, but connection programmer error.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0

  • Recently Browsing   0 members

    No registered users viewing this page.