GROM

FORD K-line TOOL

28 posts in this topic

Добавлен модуль для работы с блоками форд по K-Line 

 

IMG_20170401_124457.jpg

 

 

2020-07-24_19-13-06.jpg

 

1.png

2.png

4.png

3.png

 

 

Обсуждение в данной теме

Share this post


Link to post
Share on other sites

А через разьём эта тема работает,или только к блоку подключаться?

Share this post


Link to post
Share on other sites

Ну этот модуль позволяет хотя бы не пилить блоки.

Share this post


Link to post
Share on other sites

Уже радует.Но я обычно не так делаю, если позволяет ,беру VCM , пару минут и дело в шляпе.

Share this post


Link to post
Share on other sites

А почему бы нет,обновления идут постоянно.

программу смотрел последняя 1.04

Share this post


Link to post
Share on other sites

Скорее всего не выше 2010.

у меня есть фьюжен 2006гв, пока прибора нет сашкин. после покупки Diagspeeda сразу оплачу. будем месте тестит ))

Share this post


Link to post
Share on other sites

 

А почему бы нет,обновления идут постоянно.

программу смотрел последняя 1.04

 

Качал сегодня ,есть 1.0.0.5

Share this post


Link to post
Share on other sites

делаю сей час блок срс от фьюжина  черес к-линию читать читает писать пишет после чистки дампа и записи пишет CRASH FOUND !  ничего не пойму или я что то не так делаю или этого блока нет в модуле фото прилагаю 

IMGA0615.JPG

IMGA0616.JPG

Share this post


Link to post
Share on other sites
1 hour ago, seselis5 said:

doing this hour block of CDS fyuzhina cheres-line to read read write write after cleaning dump and write says CRASH FOUND! I do not understand or I do something wrong or this unit is not in the photo attached module 

IMGA0615.JPG

IMGA0616.JPG

Use the read dtc function and see if you get a crash code...if still crash then change line 290-3AF = FF

Share this post


Link to post
Share on other sites

Where you look read dtc function in GCT  ? now i can get Car tomorrow I check  dtc 

Share this post


Link to post
Share on other sites

При повторном считывании в зоне ошибок снова появляются данные об ошибках запалов, самого краша нет, только ошибки, модуль универсален для многих блоков, поэтому и просто ошибки попадают под "Краш"

Share this post


Link to post
Share on other sites

вот все вопросы и отпали огромное спасибо Александру 

Share this post


Link to post
Share on other sites

попытался сегодня сделать на борту на 2011 Mustang BR33-14B321-AE. Прочитал-crash found-но при записи вот что получаю

Что бы это значило?

P.S. Если при записи использую CodeCard то пишет без проблем

BR33-14B321-AE_crash.JPG

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.